|
|
|
|
|
|
Plug Wire
|
Our Price: $1.00
|
|
|
7mm replacement spark plug wire used on CR125, CR80, CR250, and many other engine applications were the coil wire and plug cap can be replaced.
Sold Per foot - 1 qty = 1 foot length. Qty's greater than 1 will be shipped uncut. For example, if you order 2, we will send 1 pc at 2' in length.
|
|
|
|
|
|
|
|
|
|
O-rings - Exhaust
|
|
|
Replacement black Viton Exhaust O-rings for CR125 O-ring manifolds, CR80 O-ring manifolds, Maxter exhaust headers and spacers, and Pavesi O-ring manifolds. Under Special Instructions, you must write in which engine you are purchasing the exhaust O-rings for.
|
|
|
|
|
|
|
|
|
|
|
94601-15000 - Circlips
|
|
Our Price: $1.99
|
|
|
Circlips - sold as a pair , for use on HRC RS Piston and Honda Stock Moto CR125
|
|
|
|
|
|
|
|
|
|
Hose Clamp - 25mm
|
|
Our Price: $1.99
|
|
|
Hose Clamp sizes from 16mm - 25mm. Used on most kart water hose applications. This is the hose clamp SwedeTech recommends on our engines. The clamp is a good quality and it has the thin clamp area to properly fit the hose fittings on most go kart applications.
|
|
|
|
|
|
|
|
|
|
EZ Clip - 3Pk
|
|
Our Price: $2.97
|
|
|
Replacement clips for SwedeTech's CR125 EZ Clip system.
|
|
|
|
|
|
|
|
|
|
|
CR125 Base Gasket - aftermarket
|
|
Our Price: $2.99
|
|
|
CR125 Base Gasket - thickness options - 0.0015", 0.005", 0.010", 0.015", 0.020"
|
|
|
|
|
|
|
|
|
|
Hose Clamp - 60mm
|
|
Our Price: $2.99
|
|
|
Hose Clamp sizes from 40mm - 60mm. Used on CR125 Intake manifold applications. This is the hose clamp SwedeTech recommends on our engines. The clamp is a good quality and it has the thin clamp area to properly fit the intake manifolds fittings on CR125 engine. This is the same clamp used on the SwedeTech Straight Manifold as well as Stock Moto. Stop losing laps from the wrong hose clamp.
|
|
|
|
|
|
|
|
|
|
PWM Screw - Top - pair
|
|
Our Price: $3.98
|
|
|
Stainless Steel Allen head screws for the Keihin PWM carburetor. Machined relief thread area keeps the screws in the top. These are machined to be the proper length so the will properly fit your carburetor. Sold in Pairs
Are you tired of rounding out the phillips on your carburetor top? Switch to these stainless screws. We also have stainless steel screws for the fuel pumps.
|
|
|
|
|
|
|
|
|
|
|
O ring - Inner
|
|
Our Price: $4.50
|
|
|
Viton O ring for engines that utilize an o ring in the head or cylinder. If you are unsure of the proper application, call us.
|
|
|
|
|
|
|
|
|
|
|
O ring - outer
|
|
Our Price: $4.50
|
|
|
Viton O ring for engines that utilize an o ring in the head or cylinder. If you are unsure of the proper application, call us.
|
|
|
|
