|
|
|
|
|
|
Plug Wire
|
Our Price: $1.00
|
|
|
7mm replacement spark plug wire used on CR125, CR80, CR250, and many other engine applications were the coil wire and plug cap can be replaced.
Sold Per foot - 1 qty = 1 foot length. Qty's greater than 1 will be shipped uncut. For example, if you order 2, we will send 1 pc at 2' in length.
|
|
|
|
|
|
|
|
|
|
O-rings - Exhaust
|
|
|
Replacement black Viton Exhaust O-rings for CR125 O-ring manifolds, CR80 O-ring manifolds, Maxter exhaust headers and spacers, and Pavesi O-ring manifolds. Under Special Instructions, you must write in which engine you are purchasing the exhaust O-rings for.
|
|
|
|
|
|
|
|
|
|
Hose Clamp - 25mm
|
|
Our Price: $1.99
|
|
|
Hose Clamp sizes from 16mm - 25mm. Used on most kart water hose applications. This is the hose clamp SwedeTech recommends on our engines. The clamp is a good quality and it has the thin clamp area to properly fit the hose fittings on most go kart applications.
|
|
|
|
|
|
|
|
|
|
|
CW14
|
|
Our Price: $2.00
|
|
|
14mm Circlip - Pair - For use in engines that use a 14mm circlip, such as the Honda CR80 or CR85. We sell this one for the piston wrist pin clips. This product is mfg by Wiseco.
|
|
|
|
|
|
|
|
|
|
|
ICC Paper Base Gasket
|
|
Our Price: $2.99
|
|
|
ICC Paper Base Gasket, customer must specify size and engine - Use text box to specify engine and size. Use the qty for each size. Example - qty 10 , text box type - TM, 0.0015 - result. We will ship 10 - 0.0015" TM base gaskets.
|
|
|
|
|
|
|
|
|
|
Hose Clamp - 60mm
|
|
Our Price: $2.99
|
|
|
Hose Clamp sizes from 40mm - 60mm. Used on CR125 Intake manifold applications. This is the hose clamp SwedeTech recommends on our engines. The clamp is a good quality and it has the thin clamp area to properly fit the intake manifolds fittings on CR125 engine. This is the same clamp used on the SwedeTech Straight Manifold as well as Stock Moto. Stop losing laps from the wrong hose clamp.
|
|
|
|
|
|
|
|
|
|
|
CR80 Base Gasket
|
|
Our Price: $3.00
|
|
|
Aftermarket CR80 base gaskets. Raise and lower your cylinder for optimum port timing. As a reference, a CR80 OEM base gasket is approximately 0.020" in thickness.
|
|
|
|
|
|
|
|
|
|
|
O ring - Inner
|
|
Our Price: $4.50
|
|
|
Viton O ring for engines that utilize an o ring in the head or cylinder. If you are unsure of the proper application, call us.
|
|
|
|
|
|
|
|
|
|
|
O ring - outer
|
|
Our Price: $4.50
|
|
|
Viton O ring for engines that utilize an o ring in the head or cylinder. If you are unsure of the proper application, call us.
|
|
|
|
|
|
|
|
|
|
|
Spring - Clutch - TM Max
|
|
Our Price: $4.50
|
|
|
Clutch spring for Maxter MXO or MXV ICC engine and the TM K9, K9B, and K9C engine. Both engines require 5 springs per clutch. SwedeTech Recommends changing the springs when you change the floaters and friction plates.
|
|
|
|
