Honda CR Engines
Parts - Accessories
Fluids, Lubricants, Cleaners
Fuel Systems and Parts
Shop by Brand
Honda CR Technical Information
ICC Technical Information
Join our mailing list!
You are here:
* Parilla Leopard Parts
* Parilla Leopard Parts
Parilla Leopard Top End Parts
Price: Low to High
Price: High to Low
10 per page
20 per page
40 per page
60 per page
100 per page
Hose Clamp - 25mm
Hose Clamp sizes from 16mm - 25mm. Used on most kart water hose applications. This is the hose clamp SwedeTech recommends on our engines. The clamp is a good quality and it has the thin clamp area to properly fit the hose fittings on most go kart applications.
NGK Spark Plug - BR10EG
Teflon Seal used in many engine applications.
Iame Parilla Leopard - order 2, ignition and pto ( Not used for the MY09 Version )
Iame HPV / KPV / Komet 100cc - order 1, ignition side
TM ICC K9, K9B, K9C - order 2, ignition and pto
Maxter ICC MXO , MXV - order 1, ignition side
Pavesi ICC - Order 1, ignition side
Vortex Rok TT - order 2, ignition and pto
RK117HL - Rebuild complete
Rebuild kit for the Tillotson HL-227A, HL-232, HL-250A-E,HL-304E HL-306A, HL-334A,AB,AA, HL-360A, HL-365B HL-383A HL-384A & B, HL-385A carburetors. This is the complete kit that includes gaskets and needle and seat. Always check pop off if your are rebuilding your carburetors.
Part number is RK117HL. For the Comer K80 , order kit RK114HL
Tillotson Cable Holder
SwedeTech has released a new product to fix a common problem with the Tillotson stock cable holder brackets. It is about time there is a true bolt on fix for the Tillotson carburetors. The bracket will work on the HL360, HL166, HL334, and many other Tillotson carburetors.
The cable holder kit includes the bracket, the throttle cable housing holder, and the return spring. This bracket will work on the Iame MY09 Leopard, Original Leopard, PRD Fireball, and many other applications
Parilla Leopard Wrist Pin
Iame Parilla Leopard Wrist Pin 14mm x 44mm
Engine Mount Butterfly-Pair
Universal engine mount clamp sits flush on the bottom side of the chassis frame rails. Many engine mounts use the butterfly clamp to properly secure and center the engine. Using the wrong clamp size will allow the engine to move causing lost chains and/or engine damage.
If you don't know what size you need, measure the diameter of the chassis frame rails. This is usually 28mm,30mm, or 32mm. The next measurement is the center to center spacing of the frame rails. This is usually 90mm or 92mm.
Sold as a pair with bolts. Available for single bolt mounts or dual bolt mounts.
Bearing Throttle Cable
Are you tired of wearing out the Tillotson throttle shafts where the cable barrel attaches to the arm. It is about time there is a true bolt on fix for the Tillotson carburetors. The Cable Assembly will work on the HL360, HL166, HL334, and many other Tillotson carburetors.
The bearing throttle cable kit includes the bolt and two nylocks to secure the bearing boss to the throttle shaft. The kit also includes the bearing and the throttle cable. Housing is sold seperately. This cable will work on the Iame MY09 Leopard, Original Leopard, PRD Fireball, and many other applications
Airbox Leopard OEM
List Price: $83.67
Add to cart for sales price
Righetti Ridolfi air box with 22mm air trumpets. No filter included. This is the airbox supplied with the Parilla Leopard Engine
Bearing, 14 x 18 x 18
Iame Wrist Pin Bearing - 14mm x 18mm x 18mm
Fits Many IAME ENGINE Packages
Become an Affiliate
Copyright © 2006 SwedeTech Racing Engines. All Rights Reserved.